The official Raspberry Pi touchscreen module offers many options and makes many other touch displays look old for a similar price. Not only is the very accurate 10-finger capacitive touch a positive, but also no GPIOs or HDMI ports are occupied.
In order to cover many topics, I have created this article, where some frequently asked questions (FAQ) are summarized.
The official 7″ Raspberry Pi touchscreen was developed by the Raspberry Pi Foundation and has a large number of options. If you have bought the display recently or are thinking about it, you can read some important points here. For this, I have made an overview. If you have more points, write a short comment and it will be added 😉
Overview 7″ Raspberry Pi Touchscreen FAQ
All of these tips have been tested on Raspbian, but should also run on Jessie or Kodi. In addition, a Raspberry Pi Model 2B or Raspberry Pi 3 should be used, if the display is not powered externally (so only via the GPIOs).
Rotating the display
One point that initially bothered me a bit is that the micro USB entrance for the power supply is on the bottom of the display. So if you do not have a 90 degree USB cable, it will be difficult to set up the display vertically.
Luckily, there is the possibility to rotate the picture automatically. It only needs to be specified for one file
sudo nano /boot/config.txt
The following is written at the end of the file:
After the restart, the image should now be rotated by 180 ° and you can turn the display over, which puts the micro USB connector on top.
Alternatively, there are the following options:
display_rotate=0 # Normal display_rotate=1 # 90 degrees display_rotate=2 # 180 degrees display_rotate=3 # 270 degrees display_rotate=0x10000 # horizontal flip display_rotate=0x20000 # vertical flip
Activating right click
If you use the touchscreen without a mouse and keyboard, you will definitely miss the right-click function. But this is easily adjustable. In this case, pressing the touchscreen for a longer time in one place triggers the same effect as right-clicking on that location.
For this, we have to edit a file
sudo nano /etc/X11/xorg.conf
and insert the following content:
Section "InputClass" Identifier "calibration" Driver "evdev" MatchProduct "FT5406 memory based driver" Option "EmulateThirdButton" "1" Option "EmulateThirdButtonTimeout" "750" Option "EmulateThirdButtonMoveThreshold" "30" EndSection
Now just reboot quickly.
After the restart, a long click should look like this:
Switching backlight on/off
Unfortunately, it is not possible to connect the display after starting the Pi, as it must already be connected and powered up at startup. However, there is the possibility of switching the backlight on and off via command line, should the display currently not be needed.
First of all, the firmware must be brought up to date, as the drivers were initially not there. Then you have to restart.
sudo rpi-update sudo reboot
Now we give the file, which is responsible for the backlight, the necessary rights:
sudo chmod 777 /sys/class/backlight/rpi_backlight/bl_power
Then the lighting can be switched off (1) or back on (0) by means of the following commands:
echo 1 > /sys/class/backlight/rpi_backlight/bl_power echo 0 > /sys/class/backlight/rpi_backlight/bl_power
If the display is used as an input, e.g. for home automation, you could possibly set a motion detector in front/above it, where the display is turned on only when needed: Operate a motion sensor PIR on the Raspberry Pi
Turning off screensaver
– Note: Below is a simpler method for current Raspbian versions –
Another point that bothers some applications is that after a few minutes of inactivity, the screen saver starts and the touchscreen turns completely black. To prevent this, we proceed as follows: First, we install a required package:
sudo apt-get install x11-xserver-utils
Then we edit the following file,
the additional content gets attached:
@xset s off @xset -dpms @xset s noblank
In addition, the line
@xscreensaver -no-splash must be commented out with a
Finally, we edit the config file
sudo nano /etc/kbd/config
and add the following parameters at the end:
BLANK_TIME=0 BLANK_DPMS=off POWERDOWN_TIME=0
This should stop the touchscreen from automatically turning off. Here there is an alternative solution, but this works (for me) only when started via
startx and not when the Pi starts in the desktop mode.
If this does not bring the desired effect (some Raspbian distributions), there is another possibility. For this we need to install xscreensaver:
sudo apt-get install xscreensaver
After that we go under Preferences -> Screensaver.
Here the screen saver can be deactivated (Disable Screen Saver):
Installing touch keyboard
Even a virtual keyboard can be very useful if you do not want to connect an additional keyboard. For this you should first boot directly into the desktop:
Under “3 Enable Boot to Desktop/Skratch” you select the second entry: “Desktop Log in as user ‘pi’ at the graphical desktop“. Then we can
sudo apt-get install at-spi2-core florence
You can find the keyboard under the Start Menu -> Accessibility. If you minimize it, there will be an icon in the top right corner of the taskbar, so you can bring it out as needed.
Every now and then one would like to take screenshots, but did not connect a keyboard with which one could press the appropriate button. Even with the virtual keyboard, this is not easily possible. But is with GNOME-screenshot, which simply creates screenshots via a GUI:
sudo apt-get install gnome-screenshot
After the quick installation you will find it under the Start menu -> Accessories -> Screenshot:
Once clicked, such a window appears:
Here are some options which can be set and then the screenshot is created. This window, which can be seen in the picture above, is not on it. After the image has been taken, you will be asked for the location, which by default will become the home directory.
Although there are KSnapshot or
scrot for the console-lovers, I think GNOME-screenshot is most suitable for the majority of users.
Making the mouse pointer disappear
In some applications (car PC, Skin Automation Panel) where a GUI is present, the mouse pointer is often annoying. To easily remove the cursor, we can install a package that will hide it:
sudo apt-get install unclutter
After a restart, the cursor is no longer visible.
There are some programs that are more suitable on the display (if you know other optimal apps for the touchscreen, I would be happy to see a comment 🙂 )
- Iceweasel – The browser is very similar to Firefox and also has many of its strengths integrated. In my tests, the default browser of Raspbian (Epiphany) often had problems playing Youtube videos in HTML5 Player. Several hotfixes did not work, so I decided to use another browser – which I think is a lot better. You can easily install it from the console:
sudo apt-get install iceweasel
- To be continued …
What is the coloured dot in the top right corner?
Maybe he has already noticed you: The blinking coloured dot in the upper right corner. This is an indication that the display is not getting enough power, e.g. if you supply it with power via the GPIOs. The problem with this is that only a certain number of milliamperes flow through it, which is just enough for the display, but it is not optimal.
You can remedy this by connecting the display directly to a power source via a micro USB cable. You will see that the picture will lighten up.
Do you have any more tips & tricks, which should not be missing? If so, feel free to leave a comment 🙂